One Operatory 20' Mobile Dental Trailer

BODY CONSTRUCTION:

The wall construction shall consist of the following:

• 2” of Tuff-R Cellotex and fiberglass batt insulation as required shall be installed in walls and ceiling.
• 7/16” thick plywood panels shall be bonded/screwed to interior walls with trim strips in-between as required. Commercial vinyl wallpaper shall be installed on all side walls and ceiling.

Door:

The insulated entry door shall have a window and be located on the passenger side front of trailer.

Flooring:

The sealed wood grain vinyl plank floor will allow no external moisture or mold buildup inside coach. Screw holes shall be sealed and sanded to smooth as required to prevent moisture from entering body and to provide a permanent smooth surface for installation of floor covering. The floor covering shall be easy clean wood grain vinyl.

Insulation:

Body shall be insulated with 2” thick closed cell foam insulation and fiberglass batt insulation with an R-factor of 14 for ceiling, sidewalls and doors to maintain the most comfortable working environment for staff and patient.

INTERIOR SPECIFICATIONS:

STEP SYSTEM:

Extra wide heavy duty manual steps shall be installed at entry door for ease of entry and exit.

Cabinetry:

All interior cabinetry shall be solid white wood fronts with 5 ply plywood sides to match. All cabinet doors will include latches to prevent opening while in transit.

Ceiling and Lighting:

The ceiling shall be an easy clean vinyl covered plywood with (3) LED lights positioned for optimal lighting.

ELECTRICAL SYSTEM:

AC Electrical System: Shall be a 120VAC single phase system rated for anticipated load. System shall include a 60A/120vac rated distribution panel configured with UL listed type circuit breakers. Circuit breakers shall be sized per component manufacturers’ recommendation.

System shall be wired using 12 gauge, 3-conductor (12/3), 600V rated, UL approved, MC commercial cable. All wiring shall be color-coded: black = hot, white = neutral, and green = ground. Additionally, wiring shall be labeled listing circuit number and/or designation at all termination points. All wiring shall adhere to applicable NEC and FMVSS regulations.

Wiring shall be supported on 16” centers with insulated, non-conductive clamps. Wire bundles shall be tied with trimmed nylon ties. Extreme care shall be taken to prevent chafing, abrasion, and exposure to high heat. Wiring run in external areas shall be encased in liquid tight conduit to further protect against the elements and mechanical damage.

Specific number and type of receptacles shall be determined during the pre-construction process.

DC Electrical System: Shall be a 12VDC, negative ground system rated for anticipated conversion load. System shall include fuse panel using blade type fuses. All circuits shall be protected from over current by fuses rated for a minimum of 125% of anticipated load. 12VDC functions shall be clearly designated by printed labels. Wiring shall be labeled listing circuit number and/or designation at all termination points.

Generator battery system shall include one (1) deep-cycle gel cell sealed battery mounted inside van in a battery case. (1) 40AMP max automatic battery maintaineris included to prevent battery overcharging.

System shall provide separate generator battery charging during operation periods when the vehicle engine is not running to prevent depletion of generator battery power.

Wiring Requirements:

All high-current battery cabling shall utilize full-length cable runs sized to load. Terminal ends shall be crimped with manufacturer recommended tooling and sealed using color-coded wrap.

All added wiring for 12VDC load runs shall be AWG 8, 10, 12, and 14, and conform to MIL-W-1678D type D. Wire terminals used shall conform to MIL-T-7928. Terminals shall be insulated with insulation grip, Type II, Class 2, and crimped with tooling recommended by manufacturer.

All added wiring shall be supported on 12” centers and bundles shall be tied with trimmed nylon ties. Entire system shall be installed to modern US automotive standards using best practices available at time of installation. Plastic/rubber grommets and/or dielectric sealants shall be used to protect wiring and/or looms where they pass through sheet metal, bulkheads, or structural supports. Convoluted polyethylene tubing shall be used to protect against chafing and abrasion where required. Extreme care shall be exercised to provide for easy serviceability of the system in future years. Extreme care shall be taken to avoid the engine manifold, engine exhaust, muffler, or any high-heat items that may subject the wiring to severe overheating during long periods of operation. These shall be the minimum acceptable wiring standards.

Floor Covering:

Install full length woodgrain vinyl plank floor covering.

Generator:

7.0 KW gasoline quiet Onan Generator with enclosure to be installed on trailer tonque. Generator fuel line will be tied into the fuel tank. Generator installation shall be in full accordance with manufacturer’s recommendations including any air flow restrictions associated with the installation method. The generator exhaust pipe shall be routed to exhaust on roadside away from entry door.
. The latches will be Southco thumb-pull with adjustable twist lock security latches, keyed alike.

Generator Controls:

Generator start, stop switch and hour meter shall be located in the suite cabinetry for easy accessibility.

HVAC:

One (1) 13,500 BTU roof mounted central heating and air conditioning system and one 11,000 BTU /5200 BTU heat with overhead delivery is provided for the recwption area. A 5200 btu baseboard heater is provided in the dental suite.

Stabilizing System:

One (1) MCI PROPRIETARY heavy-duty commercial (4) point hydrailic stabilizing system with individual controls are provided and located in the exterior hydraulics compartm

Dental Procedure Area:

The doctor and assisitant’s area will be constructed according to drawing #1001132A floor plan. The area will include the following:

• Dental chair complete with light and delivery system
• Dental stool
• Assistants stool
• Sterilizer
• Ultrsonic cleaner
• Handheld portable X-Ray
• Glove Box
• Dental Suction Unit
• Dental Air Compressor

Safety/Security:

• Fire Extinguisher
• Smoke Detector
• CO2 Detector

Shoreline Cord:

Heavy-duty rubber covered 50’ long SO 10-2 with ground shoreline cord shall be provided. Generator/shorepower transfer switch is also provided.

STORAGE:

(3) Interior white wall storage cabinets will be provided according to floor plan drawing # 1001132A,

KB Dental reserves the right to change body specifications without dimunition of purpose.

Note: Imaging systems are sold Pre-owned, As-is, Where-is, with No Warranty Expressed or Implied. All Sales Final, No Returns, No exchanges. Request Pictures and Specs. E mail questions.

TERMS:

60% down payment with signed order 20% forth week of production cycle 20% upon completion

MCI Warranty: One year parts and labor on work performed by MCI/ medical equipment warranty by medical equipment vendor/ Standard warranty by Promaster

Delivery: Approximately 8 weeks after receipt of order and down payment contingent upon timely delivery of dental equipment and trailer shell.

Up to 8 hours of training on coach system included at KB Dental, Amelia, Ohio, no driver or dental equipment training included.